NewTom (Cefla) NewTom VGi evo
CBCT capability & upgrade report
Specifications
| Sharpest resolution | 100 µm voxel |
|---|---|
| Field of view | 5–24 cm |
| Capture modes | 5x5, 8x8, 10x10, 16x16, 24x19 |
| Detector | Amorphous silicon flat panel |
| Tube voltage | 110–110 kVp |
| Tube current | 1–20 mA |
| Scan time | ~18 s (CBCT); ~90 s reconstruction |
| Released | 2014 |
| In service | 12 years |
| Status | Current |
| Export path | Standard DICOM |
| Market position | High-end large-FOV vertical CBCT for maxillofacial/ENT and implant centers |
Where the NewTom (Cefla) NewTom VGi evo stands today
- Resolution holds up: at its sharpest (100µm voxel) it's still in the fine-detail tier the newest units sell on. You are not behind on image quality.
- Field of view reaches 24cm — enough for both arches in one capture. Most practices never switch out of the small default FOV and never know they have this.
- At 12 years (2014) it's aging but not obsolete. This is exactly the window resellers target for a trade-up you may not need yet.
- Detector: Amorphous silicon flat panel.
What it already does that most practices don't use
- Multiple FOV modes (5x5, 8x8, 10x10, 16x16, 24x19). Most operators leave it on one preset — the larger modes are already paid for.
- Output/networking: standard DICOM export. That export path is what lets a scan leave the machine and become something a patient can actually look at.
Upgrade paths for the NewTom (Cefla) NewTom VGi evo
- UpgradeEvolution of NewTom VGi; extends max FOV up to 24x19 cm for full head-and-neck; ECO Scan dose-reduction mode; 0.3 mm focal spot.
- NetworkThe fastest upgrade is almost never new hardware — it's getting the volume off the machine and into a workflow. That alone changes what the box is worth to you.
- ReconfigureSwitching your default to the right FOV/scan mode for implant cases is free, and most practices never do it.
Repair vs. replace: what it costs
Repair: the dominant wear item on any dental CBCT is the X-ray tube — a replacement runs roughly $15,000-$40,000, typically every 3–7 years depending on scan volume. A larger-FOV unit like this one sits toward the upper end of that range. Budget a service contract at about $5,000–$15,000/year and software licensing around $2,000/year. A flat-panel detector is the big unknown — it isn't publicly priced, so get a manufacturer quote before assuming the worst.
Replace: replacement pricing varies by configuration and condition. Before any trade-up, the honest test is whether a networking or software path gets you most of the capability for a fraction of a new unit.
Figures are 2025–26 industry ranges for dental CBCT, not a quote for your exact unit or contract. Sources: Medical Imaging Specialists, DentalTI buyer's guide, The Dental Signal.
NewTom (Cefla) NewTom VGi evo — common questions
- Can Alvea use scans from the NewTom (Cefla) NewTom VGi evo?
- Yes. The NewTom (Cefla) NewTom VGi evo exports a standard DICOM volume, and Alvea converts that volume into a chairside 3D model of the patient's jaw — no new hardware and no new scan. It runs off the cone-beam you already take.
- How much does it cost to repair a NewTom (Cefla) NewTom VGi evo?
- The dominant repair on any dental CBCT is the X-ray tube, which runs roughly $15,000-$40,000 and is typically replaced every 3–7 years by scan volume. Annual service contracts run about $5,000–$15,000, and a flat-panel detector is quoted by the manufacturer rather than listed publicly. These are 2025–26 industry ranges, not a quote for a specific unit.
- What is the field of view on the NewTom (Cefla) NewTom VGi evo?
- The NewTom (Cefla) NewTom VGi evo reaches 24 cm, enough to capture both arches in one scan — a mode most practices never switch to.
See what a NewTom (Cefla) NewTom VGi evo scan becomes.
Run the free, independent report on your exact unit — then turn one of your own scans into a 3D model the patient can see before they decide. No new hardware, no new scan.
Check my NewTom (Cefla) unit → Try it on one of my scans — first one's free