Can Alvea use scans from the i-CAT (Dentsply Sirona) i-CAT FLX V17?

Yes. The i-CAT (Dentsply Sirona) i-CAT FLX V17 exports a standard DICOM volume, and Alvea converts that volume into a chairside 3D model of the patient's jaw — no new hardware and no new scan. It runs off the cone-beam you already take.

How much does it cost to repair a i-CAT (Dentsply Sirona) i-CAT FLX V17?

The dominant repair on any dental CBCT is the X-ray tube, which runs roughly $15,000-$40,000 and is typically replaced every 3–7 years by scan volume. Annual service contracts run about $5,000–$15,000, and a flat-panel detector is quoted by the manufacturer rather than listed publicly. These are 2025–26 industry ranges, not a quote for a specific unit.

What is the field of view on the i-CAT (Dentsply Sirona) i-CAT FLX V17?

The i-CAT (Dentsply Sirona) i-CAT FLX V17 reaches 23 cm, enough to capture both arches in one scan — a mode most practices never switch to.

i-CAT (Dentsply Sirona)current

i-CAT (Dentsply Sirona) i-CAT FLX V17
CBCT capability & upgrade report

Name: i-CAT (Dentsply Sirona) i-CAT FLX V17
Brand: i-CAT (Dentsply Sirona)

i-CAT FLX V-Series · released 2016 · 10 yrs in service · current

✓ Works with Alvea. Your i-CAT (Dentsply Sirona) i-CAT FLX V17 produces the DICOM volume Alvea works from — its scans convert to a chairside 3D model with no new hardware. It runs off the cone-beam you already take; nothing to install on the machine.

Specifications

Sharpest resolution	125 µm voxel
Field of view	8–23 cm
Capture modes	8x5, 8x8, 16x4, 16x6, 16x8, 16x10, 16x11, 16x13, 23x17
Detector	Amorphous silicon flat panel (24.2 x 19.3 cm sensor, 1536 x 1920 matrix, 127 um pixel pitch)
Tube voltage	120–120 kVp
Tube current	3–7 mA
Scan time	4.8 s (13x16 ceph-height 3D) up to 40 s
Pan / Ceph	Integrated 2D + 3D
Released	2016
In service	10 years
Status	Current
Export path	Standard DICOM
Market position	Top large-FOV V-Series for full cranial-height 3D, ortho and airway; flagship of the current i-CAT line

Where the i-CAT (Dentsply Sirona) i-CAT FLX V17 stands today

Resolution is solid mainstream (125µm at best). Fine for implant visualization; the newest high-res units go finer, but the real-world difference is marginal for case communication.
Field of view reaches 23cm — enough for both arches in one capture. Most practices never switch out of the small default FOV and never know they have this.
At 10 years (2016) it's aging but not obsolete. This is exactly the window resellers target for a trade-up you may not need yet.
Detector: Amorphous silicon flat panel (24.2 x 19.3 cm sensor, 1536 x 1920 matrix, 127 um pixel pitch).

What it already does that most practices don't use

Multiple FOV modes (8x5, 8x8, 16x4, 16x6, 16x8, 16x10, 16x11, 16x13, 23x17). Most operators leave it on one preset — the larger modes are already paid for.
The same unit does panoramic/ceph as well as 3D — one capture surface you may be sending out for.
Output/networking: standard DICOM export. That export path is what lets a scan leave the machine and become something a patient can actually look at.

Upgrade paths for the i-CAT (Dentsply Sirona) i-CAT FLX V17

UpgradeTop tier; full 23 dia x 17 cm FOV unlocked; V8/V10 units upgrade to V17 by software license
NetworkThe fastest upgrade is almost never new hardware — it's getting the volume off the machine and into a workflow. That alone changes what the box is worth to you.
ReconfigureSwitching your default to the right FOV/scan mode for implant cases is free, and most practices never do it.

Repair vs. replace: what it costs

Repair: the dominant wear item on any dental CBCT is the X-ray tube — a replacement runs roughly $15,000-$40,000, typically every 3–7 years depending on scan volume. A larger-FOV unit like this one sits toward the upper end of that range. Budget a service contract at about $5,000–$15,000/year and software licensing around $2,000/year. A flat-panel detector is the big unknown — it isn't publicly priced, so get a manufacturer quote before assuming the worst.

Replace: replacement pricing varies by configuration and condition. Before any trade-up, the honest test is whether a networking or software path gets you most of the capability for a fraction of a new unit.

Figures are 2025–26 industry ranges for dental CBCT, not a quote for your exact unit or contract. Sources: Medical Imaging Specialists, DentalTI buyer's guide, The Dental Signal.

i-CAT (Dentsply Sirona) i-CAT FLX V17 — common questions

Can Alvea use scans from the i-CAT (Dentsply Sirona) i-CAT FLX V17?: Yes. The i-CAT (Dentsply Sirona) i-CAT FLX V17 exports a standard DICOM volume, and Alvea converts that volume into a chairside 3D model of the patient's jaw — no new hardware and no new scan. It runs off the cone-beam you already take.
How much does it cost to repair a i-CAT (Dentsply Sirona) i-CAT FLX V17?: The dominant repair on any dental CBCT is the X-ray tube, which runs roughly $15,000-$40,000 and is typically replaced every 3–7 years by scan volume. Annual service contracts run about $5,000–$15,000, and a flat-panel detector is quoted by the manufacturer rather than listed publicly. These are 2025–26 industry ranges, not a quote for a specific unit.
What is the field of view on the i-CAT (Dentsply Sirona) i-CAT FLX V17?: The i-CAT (Dentsply Sirona) i-CAT FLX V17 reaches 23 cm, enough to capture both arches in one scan — a mode most practices never switch to.

Your cone-beam, chairside

See what a i-CAT (Dentsply Sirona) i-CAT FLX V17 scan becomes.

Run the free, independent report on your exact unit — then turn one of your own scans into a 3D model the patient can see before they decide. No new hardware, no new scan.

Check my i-CAT (Dentsply Sirona) unit → Try it on one of my scans — first one's free

Independent by design. Alvea makes nothing you'd buy from a CBCT vendor — so this report has no reason to push you toward a sale. It reads your machine, not your patients. This is an equipment capability report, not clinical guidance.