Pointnix Point 3D Combi 500
CBCT capability & upgrade report
Specifications
| Sharpest resolution | 100 µm voxel |
|---|---|
| Field of view | 12–14 cm |
| Capture modes | 12x9, 14x9 |
| Tube voltage | 50–90 kVp |
| Tube current | 4–10 mA |
| Scan time | CBCT up to ~17s (HD mode) |
| Pan / Ceph | Integrated 2D + 3D |
| Released | 2016 |
| In service | 10 years |
| Status | Current |
| Export path | Standard DICOM |
| Market position | Korean medium/large-FOV 4-in-1 with stitched CBCT |
Where the Pointnix Point 3D Combi 500 stands today
- Resolution holds up: at its sharpest (100µm voxel) it's still in the fine-detail tier the newest units sell on. You are not behind on image quality.
- Field of view reaches 14cm — enough for both arches in one capture. Most practices never switch out of the small default FOV and never know they have this.
- At 10 years (2016) it's aging but not obsolete. This is exactly the window resellers target for a trade-up you may not need yet.
What it already does that most practices don't use
- Multiple FOV modes (12x9, 14x9). Most operators leave it on one preset — the larger modes are already paid for.
- The same unit does panoramic/ceph as well as 3D — one capture surface you may be sending out for.
- Output/networking: standard DICOM export. That export path is what lets a scan leave the machine and become something a patient can actually look at.
Upgrade paths for the Pointnix Point 3D Combi 500
- Upgrade4-in-1 (CBCT/pano/ceph/model scan); stitching CBCT; 500C vs 500S differ by ceph config; 14-bit.
- NetworkThe fastest upgrade is almost never new hardware — it's getting the volume off the machine and into a workflow. That alone changes what the box is worth to you.
- ReconfigureSwitching your default to the right FOV/scan mode for implant cases is free, and most practices never do it.
Repair vs. replace: what it costs
Repair: the dominant wear item on any dental CBCT is the X-ray tube — a replacement runs roughly $15,000-$40,000, typically every 3–7 years depending on scan volume. A larger-FOV unit like this one sits toward the upper end of that range. Budget a service contract at about $5,000–$15,000/year and software licensing around $2,000/year. A flat-panel detector is the big unknown — it isn't publicly priced, so get a manufacturer quote before assuming the worst.
Replace: replacement pricing varies by configuration and condition. Before any trade-up, the honest test is whether a networking or software path gets you most of the capability for a fraction of a new unit.
Figures are 2025–26 industry ranges for dental CBCT, not a quote for your exact unit or contract. Sources: Medical Imaging Specialists, DentalTI buyer's guide, The Dental Signal.
Pointnix Point 3D Combi 500 — common questions
- Can Alvea use scans from the Pointnix Point 3D Combi 500?
- Yes. The Pointnix Point 3D Combi 500 exports a standard DICOM volume, and Alvea converts that volume into a chairside 3D model of the patient's jaw — no new hardware and no new scan. It runs off the cone-beam you already take.
- How much does it cost to repair a Pointnix Point 3D Combi 500?
- The dominant repair on any dental CBCT is the X-ray tube, which runs roughly $15,000-$40,000 and is typically replaced every 3–7 years by scan volume. Annual service contracts run about $5,000–$15,000, and a flat-panel detector is quoted by the manufacturer rather than listed publicly. These are 2025–26 industry ranges, not a quote for a specific unit.
- What is the field of view on the Pointnix Point 3D Combi 500?
- The Pointnix Point 3D Combi 500 reaches 14 cm, enough to capture both arches in one scan — a mode most practices never switch to.
See what a Pointnix Point 3D Combi 500 scan becomes.
Run the free, independent report on your exact unit — then turn one of your own scans into a 3D model the patient can see before they decide. No new hardware, no new scan.
Check my Pointnix unit → Try it on one of my scans — first one's free