Can Alvea use scans from the J. Morita 3D Accuitomo 80?

Yes. The J. Morita 3D Accuitomo 80 exports a standard DICOM volume, and Alvea converts that volume into a chairside 3D model of the patient's jaw — no new hardware and no new scan. It runs off the cone-beam you already take.

Is the J. Morita 3D Accuitomo 80 discontinued, and what replaced it?

The J. Morita 3D Accuitomo 80 is no longer sold new; its successor is the 3D Accuitomo 170. An aging unit is rarely a reason to replace on its own — parts, service and a software/networking path usually keep it clinically current for far less than a new machine.

How much does a J. Morita 3D Accuitomo 80 cost?

A comparable J. Morita 3D Accuitomo 80 runs roughly used only. Before replacing, weigh whether a networking or software path gets you most of the capability for a fraction of that.

How much does it cost to repair a J. Morita 3D Accuitomo 80?

The dominant repair on any dental CBCT is the X-ray tube, which runs roughly $15,000-$40,000 and is typically replaced every 3–7 years by scan volume. Annual service contracts run about $5,000–$15,000, and a flat-panel detector is quoted by the manufacturer rather than listed publicly. These are 2025–26 industry ranges, not a quote for a specific unit.

What is the field of view on the J. Morita 3D Accuitomo 80?

The J. Morita 3D Accuitomo 80 reaches 8 cm, single-arch range suited to localized implant work.

J. Moritadiscontinued

J. Morita 3D Accuitomo 80
CBCT capability & upgrade report

Name: J. Morita 3D Accuitomo 80
Brand: J. Morita

3D Accuitomo (dedicated CBCT) · released 2007 · 19 yrs in service · discontinued

✓ Works with Alvea. Your J. Morita 3D Accuitomo 80 produces the DICOM volume Alvea works from — its scans convert to a chairside 3D model with no new hardware. It runs off the cone-beam you already take; nothing to install on the machine.

Specifications

Sharpest resolution	80 µm voxel
Field of view	4–8 cm
Capture modes	4x4, 6x6, 8x8
Detector	Flat panel
Tube voltage	60–90 kVp
Tube current	1–10 mA
Scan time	~17.5 s (360 deg)
Released	2007
In service	19 years
Status	Discontinued
Export path	Standard DICOM
Current successor	3D Accuitomo 170
Market position	Legacy small-FOV high-resolution diagnostic CBCT

Where the J. Morita 3D Accuitomo 80 stands today

Resolution holds up: at its sharpest (80µm voxel) it's still in the fine-detail tier the newest units sell on. You are not behind on image quality.
Field of view tops out at 8cm — single-arch range. Good for localized implant work; whole-jaw cases need the larger-FOV path (below).
It's 19 years old (2007) — legacy hardware. The question isn't "is it old," it's "does a networking/software path get you current for a fraction of a new unit." Usually yes.
Detector: Flat panel.
This model is no longer sold new (succeeded by the 3D Accuitomo 170) — which means parts, service, and software support are the thing to verify before any new spend.

What it already does that most practices don't use

Multiple FOV modes (4x4, 6x6, 8x8). Most operators leave it on one preset — the larger modes are already paid for.
Output/networking: standard DICOM export. That export path is what lets a scan leave the machine and become something a patient can actually look at.

Upgrade paths for the J. Morita 3D Accuitomo 80

UpgradeFlat-panel Accuitomo with FOV up to Ø80xH80; FDA model MCT-1F8; zoom reconstruction high-res; superseded by Accuitomo 170 which adds larger FOV.
SuccessorThe 3D Accuitomo 170 is the current successor — useful as a yardstick for what actually changed, not an automatic reason to buy it.
NetworkThe fastest upgrade is almost never new hardware — it's getting the volume off the machine and into a workflow. That alone changes what the box is worth to you.
ReconfigureSwitching your default to the right FOV/scan mode for implant cases is free, and most practices never do it.

Repair vs. replace: what it costs

Repair: the dominant wear item on any dental CBCT is the X-ray tube — a replacement runs roughly $15,000-$40,000, typically every 3–7 years depending on scan volume. Budget a service contract at about $5,000–$15,000/year and software licensing around $2,000/year. A flat-panel detector is the big unknown — it isn't publicly priced, so get a manufacturer quote before assuming the worst.

Parts & service (legacy unit): because this model is no longer sold new, parts and service availability — not the sticker — decide whether a repair is worth it. Confirm both before any spend.

Replace: a comparable unit runs roughly used only. The honest test before spending that is whether a networking or software path gets you most of the capability for a fraction of it — for an aging machine, it usually does.

Figures are 2025–26 industry ranges for dental CBCT, not a quote for your exact unit or contract. Sources: Medical Imaging Specialists, DentalTI buyer's guide, The Dental Signal.

J. Morita 3D Accuitomo 80 — common questions

Can Alvea use scans from the J. Morita 3D Accuitomo 80?: Yes. The J. Morita 3D Accuitomo 80 exports a standard DICOM volume, and Alvea converts that volume into a chairside 3D model of the patient's jaw — no new hardware and no new scan. It runs off the cone-beam you already take.
Is the J. Morita 3D Accuitomo 80 discontinued, and what replaced it?: The J. Morita 3D Accuitomo 80 is no longer sold new; its successor is the 3D Accuitomo 170. An aging unit is rarely a reason to replace on its own — parts, service and a software/networking path usually keep it clinically current for far less than a new machine.
How much does a J. Morita 3D Accuitomo 80 cost?: A comparable J. Morita 3D Accuitomo 80 runs roughly used only. Before replacing, weigh whether a networking or software path gets you most of the capability for a fraction of that.
How much does it cost to repair a J. Morita 3D Accuitomo 80?: The dominant repair on any dental CBCT is the X-ray tube, which runs roughly $15,000-$40,000 and is typically replaced every 3–7 years by scan volume. Annual service contracts run about $5,000–$15,000, and a flat-panel detector is quoted by the manufacturer rather than listed publicly. These are 2025–26 industry ranges, not a quote for a specific unit.
What is the field of view on the J. Morita 3D Accuitomo 80?: The J. Morita 3D Accuitomo 80 reaches 8 cm, single-arch range suited to localized implant work.

Your cone-beam, chairside

See what a J. Morita 3D Accuitomo 80 scan becomes.

Run the free, independent report on your exact unit — then turn one of your own scans into a 3D model the patient can see before they decide. No new hardware, no new scan.

Check my J. Morita unit → Try it on one of my scans — first one's free

Independent by design. Alvea makes nothing you'd buy from a CBCT vendor — so this report has no reason to push you toward a sale. It reads your machine, not your patients. This is an equipment capability report, not clinical guidance.