Ray (RAYSCAN) RAYSCAN Studio
CBCT capability & upgrade report
Specifications
| Field of view | up to 20 cm |
|---|---|
| Capture modes | Free FOV up to 20x20 |
| Scan time | family 4.9-16s |
| Pan / Ceph | Integrated 2D + 3D |
| Released | 2019 |
| In service | 7 years |
| Status | Current |
| Export path | Standard DICOM |
| Market position | Premium large-FOV 5-in-1 'virtual patient' system for OMFS/ortho/sleep |
Where the Ray (RAYSCAN) RAYSCAN Studio stands today
- Field of view reaches 20cm — enough for both arches in one capture. Most practices never switch out of the small default FOV and never know they have this.
- At 7 years (2019) it's current-generation. There is no hardware reason to replace it — the value left on the table is in how you use it.
What it already does that most practices don't use
- The same unit does panoramic/ceph as well as 3D — one capture surface you may be sending out for.
- Output/networking: standard DICOM export. That export path is what lets a scan leave the machine and become something a patient can actually look at.
Upgrade paths for the Ray (RAYSCAN) RAYSCAN Studio
- UpgradeLarge-FOV (up to 20x20) Free FOV; true 5-in-1 (CBCT + pano + ceph in a single scan, no ceph arm, plus 3D face scan and CT impression/digital tray).
- NetworkThe fastest upgrade is almost never new hardware — it's getting the volume off the machine and into a workflow. That alone changes what the box is worth to you.
- ReconfigureSwitching your default to the right FOV/scan mode for implant cases is free, and most practices never do it.
Repair vs. replace: what it costs
Repair: the dominant wear item on any dental CBCT is the X-ray tube — a replacement runs roughly $15,000-$40,000, typically every 3–7 years depending on scan volume. A larger-FOV unit like this one sits toward the upper end of that range. Budget a service contract at about $5,000–$15,000/year and software licensing around $2,000/year. A flat-panel detector is the big unknown — it isn't publicly priced, so get a manufacturer quote before assuming the worst.
Replace: replacement pricing varies by configuration and condition. Before any trade-up, the honest test is whether a networking or software path gets you most of the capability for a fraction of a new unit.
Figures are 2025–26 industry ranges for dental CBCT, not a quote for your exact unit or contract. Sources: Medical Imaging Specialists, DentalTI buyer's guide, The Dental Signal.
Ray (RAYSCAN) RAYSCAN Studio — common questions
- Can Alvea use scans from the Ray (RAYSCAN) RAYSCAN Studio?
- Yes. The Ray (RAYSCAN) RAYSCAN Studio exports a standard DICOM volume, and Alvea converts that volume into a chairside 3D model of the patient's jaw — no new hardware and no new scan. It runs off the cone-beam you already take.
- How much does it cost to repair a Ray (RAYSCAN) RAYSCAN Studio?
- The dominant repair on any dental CBCT is the X-ray tube, which runs roughly $15,000-$40,000 and is typically replaced every 3–7 years by scan volume. Annual service contracts run about $5,000–$15,000, and a flat-panel detector is quoted by the manufacturer rather than listed publicly. These are 2025–26 industry ranges, not a quote for a specific unit.
- What is the field of view on the Ray (RAYSCAN) RAYSCAN Studio?
- The Ray (RAYSCAN) RAYSCAN Studio reaches 20 cm, enough to capture both arches in one scan — a mode most practices never switch to.
See what a Ray (RAYSCAN) RAYSCAN Studio scan becomes.
Run the free, independent report on your exact unit — then turn one of your own scans into a 3D model the patient can see before they decide. No new hardware, no new scan.
Check my Ray (RAYSCAN) unit → Try it on one of my scans — first one's free