Planmeca ProMax 3D Max
CBCT capability & upgrade report
Specifications
| Sharpest resolution | 75 µm voxel |
|---|---|
| Field of view | 5–23 cm |
| Capture modes | 5x5.5, 10x5.5, 10x9, 13x5.5, 13x9, 10x13, 13x13, 13x16, 23x16, 23x26 |
| Detector | CMOS flat panel |
| Tube voltage | 54–96 kVp |
| Tube current | 1–14 mA |
| Scan time | 9-40 s |
| Pan / Ceph | Integrated 2D + 3D |
| Released | 2009 |
| In service | 17 years |
| Status | Discontinued |
| Export path | DICOM export via Planmeca Romexis |
| Current successor | Planmeca Viso G7 |
| Market position | Large-volume maxillofacial/ortho/airway; ProMax flagship before Viso |
Where the Planmeca ProMax 3D Max stands today
- Resolution holds up: at its sharpest (75µm voxel) it's still in the fine-detail tier the newest units sell on. You are not behind on image quality.
- Field of view reaches 23cm — enough for both arches in one capture. Most practices never switch out of the small default FOV and never know they have this.
- It's 17 years old (2009) — legacy hardware. The question isn't "is it old," it's "does a networking/software path get you current for a fraction of a new unit." Usually yes.
- Detector: CMOS flat panel.
- This model is no longer sold new (succeeded by the Planmeca Viso G7) — which means parts, service, and software support are the thing to verify before any new spend.
What it already does that most practices don't use
- Multiple FOV modes (5x5.5, 10x5.5, 10x9, 13x5.5, 13x9, 10x13, 13x13, 13x16, 23x16, 23x26). Most operators leave it on one preset — the larger modes are already paid for.
- The same unit does panoramic/ceph as well as 3D — one capture surface you may be sending out for.
- Output/networking: DICOM export via Planmeca Romexis. That export path is what lets a scan leave the machine and become something a patient can actually look at.
Upgrade paths for the Planmeca ProMax 3D Max
- UpgradeLargest-FOV ProMax; full-skull 23x26 cm. Optional pan added 2013. SCARA field-upgradeable
- SuccessorThe Planmeca Viso G7 is the current successor — useful as a yardstick for what actually changed, not an automatic reason to buy it.
- NetworkThe fastest upgrade is almost never new hardware — it's getting the volume off the machine and into a workflow. That alone changes what the box is worth to you.
- ReconfigureSwitching your default to the right FOV/scan mode for implant cases is free, and most practices never do it.
Repair vs. replace: what it costs
Repair: the dominant wear item on any dental CBCT is the X-ray tube — a replacement runs roughly $15,000-$40,000, typically every 3–7 years depending on scan volume. A larger-FOV unit like this one sits toward the upper end of that range. Budget a service contract at about $5,000–$15,000/year and software licensing around $2,000/year. A flat-panel detector is the big unknown — it isn't publicly priced, so get a manufacturer quote before assuming the worst.
Parts & service (legacy unit): because this model is no longer sold new, parts and service availability — not the sticker — decide whether a repair is worth it. Confirm both before any spend.
Replace: a comparable unit runs roughly used ~$40k-70k. The honest test before spending that is whether a networking or software path gets you most of the capability for a fraction of it — for an aging machine, it usually does.
Figures are 2025–26 industry ranges for dental CBCT, not a quote for your exact unit or contract. Sources: Medical Imaging Specialists, DentalTI buyer's guide, The Dental Signal.
Planmeca ProMax 3D Max — common questions
- Can Alvea use scans from the Planmeca ProMax 3D Max?
- Yes. The Planmeca ProMax 3D Max exports a standard DICOM volume, and Alvea converts that volume into a chairside 3D model of the patient's jaw — no new hardware and no new scan. It runs off the cone-beam you already take.
- Is the Planmeca ProMax 3D Max discontinued, and what replaced it?
- The Planmeca ProMax 3D Max is no longer sold new; its successor is the Planmeca Viso G7. An aging unit is rarely a reason to replace on its own — parts, service and a software/networking path usually keep it clinically current for far less than a new machine.
- How much does a Planmeca ProMax 3D Max cost?
- A comparable Planmeca ProMax 3D Max runs roughly used ~$40k-70k. Before replacing, weigh whether a networking or software path gets you most of the capability for a fraction of that.
- How much does it cost to repair a Planmeca ProMax 3D Max?
- The dominant repair on any dental CBCT is the X-ray tube, which runs roughly $15,000-$40,000 and is typically replaced every 3–7 years by scan volume. Annual service contracts run about $5,000–$15,000, and a flat-panel detector is quoted by the manufacturer rather than listed publicly. These are 2025–26 industry ranges, not a quote for a specific unit.
- What is the field of view on the Planmeca ProMax 3D Max?
- The Planmeca ProMax 3D Max reaches 23 cm, enough to capture both arches in one scan — a mode most practices never switch to.
See what a Planmeca ProMax 3D Max scan becomes.
Run the free, independent report on your exact unit — then turn one of your own scans into a 3D model the patient can see before they decide. No new hardware, no new scan.
Check my Planmeca unit → Try it on one of my scans — first one's free