KaVo OP 3D Vision
CBCT capability & upgrade report
Specifications
| Sharpest resolution | 125 µm voxel |
|---|---|
| Field of view | 5–23 cm |
| Capture modes | 5x5, 8x8, 16x6, 16x13, 17x13 (V17), 23x17 (V17, stitched) |
| Detector | amorphous silicon flat panel |
| Tube voltage | 90–120 kVp |
| Tube current | 3–8 mA |
| Scan time | QuickScan+ ~4.8 s; standard scans up to ~26 s |
| Released | 2016 |
| In service | 10 years |
| Status | Discontinued |
| Export path | DICOM 3.0 export |
| Market position | Dedicated large-volume CBCT for oral surgery, orthodontics, airway and full craniofacial |
Where the KaVo OP 3D Vision stands today
- Resolution is solid mainstream (125µm at best). Fine for implant visualization; the newest high-res units go finer, but the real-world difference is marginal for case communication.
- Field of view reaches 23cm — enough for both arches in one capture. Most practices never switch out of the small default FOV and never know they have this.
- At 10 years (2016) it's aging but not obsolete. This is exactly the window resellers target for a trade-up you may not need yet.
- Detector: amorphous silicon flat panel.
- This model is no longer sold new — which means parts, service, and software support are the thing to verify before any new spend.
What it already does that most practices don't use
- Multiple FOV modes (5x5, 8x8, 16x6, 16x13, 17x13 (V17), 23x17 (V17, stitched)). Most operators leave it on one preset — the larger modes are already paid for.
- Output/networking: DICOM 3.0 export. That export path is what lets a scan leave the machine and become something a patient can actually look at.
Upgrade paths for the KaVo OP 3D Vision
- UpgradeLarge-FOV seated/standing CBCT derived from the i-CAT FLX / 3D eXam platform. Two configurations: V10 (up to ~16 cm FOV) and V17 (up to 23x17 cm). Selectable voxels 0.125-0.400 mm; QuickScan+ low-dose mode. Dedicated CBCT (not a pan/ceph combo).
- NetworkThe fastest upgrade is almost never new hardware — it's getting the volume off the machine and into a workflow. That alone changes what the box is worth to you.
- ReconfigureSwitching your default to the right FOV/scan mode for implant cases is free, and most practices never do it.
Repair vs. replace: what it costs
Repair: the dominant wear item on any dental CBCT is the X-ray tube — a replacement runs roughly $15,000-$40,000, typically every 3–7 years depending on scan volume. A larger-FOV unit like this one sits toward the upper end of that range. Budget a service contract at about $5,000–$15,000/year and software licensing around $2,000/year. A flat-panel detector is the big unknown — it isn't publicly priced, so get a manufacturer quote before assuming the worst.
Parts & service (legacy unit): because this model is no longer sold new, parts and service availability — not the sticker — decide whether a repair is worth it. Confirm both before any spend.
Replace: a comparable unit runs roughly ~$80k-$150k used/new (discontinued). The honest test before spending that is whether a networking or software path gets you most of the capability for a fraction of it — for an aging machine, it usually does.
Figures are 2025–26 industry ranges for dental CBCT, not a quote for your exact unit or contract. Sources: Medical Imaging Specialists, DentalTI buyer's guide, The Dental Signal.
KaVo OP 3D Vision — common questions
- Can Alvea use scans from the KaVo OP 3D Vision?
- Yes. The KaVo OP 3D Vision exports a standard DICOM volume, and Alvea converts that volume into a chairside 3D model of the patient's jaw — no new hardware and no new scan. It runs off the cone-beam you already take.
- Is the KaVo OP 3D Vision discontinued, and what replaced it?
- The KaVo OP 3D Vision is no longer sold new. An aging unit is rarely a reason to replace on its own — parts, service and a software/networking path usually keep it clinically current for far less than a new machine.
- How much does a KaVo OP 3D Vision cost?
- A comparable KaVo OP 3D Vision runs roughly ~$80k-$150k used/new (discontinued). Before replacing, weigh whether a networking or software path gets you most of the capability for a fraction of that.
- How much does it cost to repair a KaVo OP 3D Vision?
- The dominant repair on any dental CBCT is the X-ray tube, which runs roughly $15,000-$40,000 and is typically replaced every 3–7 years by scan volume. Annual service contracts run about $5,000–$15,000, and a flat-panel detector is quoted by the manufacturer rather than listed publicly. These are 2025–26 industry ranges, not a quote for a specific unit.
- What is the field of view on the KaVo OP 3D Vision?
- The KaVo OP 3D Vision reaches 23 cm, enough to capture both arches in one scan — a mode most practices never switch to.
See what a KaVo OP 3D Vision scan becomes.
Run the free, independent report on your exact unit — then turn one of your own scans into a 3D model the patient can see before they decide. No new hardware, no new scan.
Check my KaVo unit → Try it on one of my scans — first one's free